How to remove the front and rear driveaxles on BMW 330i?

For AWD models, when removing the front, start by having the vehicle on its wheels, remove the wheel trim/hub cap, and loosen the Axle Shaft retaining nut or bolt and the wheel bolts. Before loosening the Axle Shaft nut, use a hammer and punch to push out the staked portion of the nut. On F-series chassis models, always replace the Axle Shaft bolt and small compression spring whenever they are removed. Block the rear wheels, raise the vehicle front, support on jackstands, and take off the front wheel. Detach the ABS wheel speed sensor, set the brake caliper aside without disconnecting the brake fluid hose. Disconnect the stabilizer bar link from the strut and separate the tension strut and control arm from the knuckle. Push the Axle Shaft stub through the hub while pulling the steering knuckle outwards. Pry the inboard CV joint away from the front differential housing. For the right Axle Shaft, pry against the bearing bracket. For installation, remove the snap-ring from the Axle Shaft's inboard end and install a new one. Lubricate the nut-to-wheel bearing area, tighten the nut to the needed torque without oiling the threads, stake the nut post-tightening, and add new inner joint retaining bolts and plates, tightening them to the necessary torque.For the rear, with the vehicle on its wheels, remove the wheel trim/hub cap and loosen the Axle Shaft retaining nut and wheel bolts. Push out the staked portion of the Axle Shaft nut using a hammer and punch. Block the front wheels, raise the rear, and support on jackstands before removing the rear wheel. For E-series chassis, if removing the left Axle Shaft, remove the exhaust system tailpipe. Loosen and remove the stabilizer bar mounts, pivot the bar downwards. Mark alignment, then loosen and remove bolts securing the Axle Shaft CV joint to the rear differential. Withdraw the outer CV joint from the hub assembly. Tap or press it out if needed and then remove the driveshaft.For F-series chassis models, remove the Axle Shaft nut, push the axle slightly inwards, support the rear differential, then remove the mounting bolt/nuts and lower the differential. Pry the inboard CV joint away from the rear differential housing until the Axle Shaft is free, slide the Axle Shaft out of the differential, and have a pan ready for spilled lubricant. For installation, note the following: On E-series chassis models, install new inner joint retaining bolts and plates and tighten. On F-series chassis models, check the dust plate, replace the circlip on the Axle Shaft's end, and coat the seal contact with differential oil. Slide the Axle Shaft into the rear differential until an audible click is heard. Reinstall the rear differential assembly and refill it. Lubricate the nut-to-hub flange area, tighten the nut without oiling the threads, and then stake the nut once tightened.

Genuine BMW 330i Axle Shaft

Car Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Series

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

23 Axle Shafts found

View related parts
BMW 330i Right Cv Axle Assembly
Part Number: 33208680350
$1052.01 MSRP: $1376.47
You Save: $324.46 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Output Shaft, Right; Axle Assembly
- Position: Passenger Side
- Replaces: 33-20-7-597-678
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2017-2018 BMW 330i | Sedan(F30)
View related parts
BMW 330i Cv Axle Assembly Rear Left
Part Number: 33208680351
$1052.01 MSRP: $1376.47
You Save: $324.46 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Output Shaft, Left; Axle Assembly
- Position: Rear Driver Side
- Replaces: 33-20-7-597-677
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2017-2018 BMW 330i | Sedan(F30)
View related parts
BMW 330i OUTPUT SHAFT RIGHT REAR
Part Number: 33205A733B6
$1073.05 MSRP: $1404.00
You Save: $330.95 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Axle Assembly, Axle Shaft
- Position: Rear Passenger Side
- Replaces: 33-20-9-452-904, 33-20-8-666-074
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2021-2023 BMW 330i | 4 Cyl 2.0 L GAS
View related parts
BMW 330i Rear Right Axle Shaft
Part Number: 33207580946
$946.82 MSRP: $1238.83
You Save: $292.01 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Exchange Output Shaft, Right; Axle Assembly
- Position: Rear Passenger Side
- Replaced by: 33207580326
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2006 BMW 330i | Sedan(E90)
View related parts
BMW 330i Cv Axle Assembly Left
Part Number: 33217504521
$753.74 MSRP: $792.67
You Save: $38.93 (5%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Exchange. Output Shaft, Left; Axle Assembly
- Position: Driver Side
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2001-2005 BMW 330i | Sedan(E46)
View related parts
BMW 330i Left Output Shaft
Part Number: 33207637445
$1052.01 MSRP: $1376.47
You Save: $324.46 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Output Shaft, Left; Axle Assembly
- Position: Driver Side
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2017-2018 BMW 330i | Sedan(F30)
View related parts
BMW 330i OUTPUT SHAFT, REAR RIGHT
Part Number: 33208487124
$1073.05 MSRP: $1404.00
You Save: $330.95 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2023-2024 BMW 330i | 4 Cyl 2.0 L GAS
- 2019-2020 BMW 330i | Sedan(G20)
View related parts
BMW 330i Cv Axle Assembly Rear Left
Part Number: 33207561795
$511.37 MSRP: $761.38
You Save: $250.01 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Exchange. Output Shaft, Left; Axle Assembly
- Position: Rear Driver Side
- Replaced by: 33217559085
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2006 BMW 330i | Sedan(E90)
View related parts
BMW 330i Rear Output Shaft - Right
Part Number: 33207561796
$533.81 MSRP: $693.91
You Save: $160.10 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Exchange Output Shaft, Right; Axle Assembly
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2006 BMW 330i | Sedan(E90)
View related parts
BMW 330i Rear Left Cv Axle Assembly
Part Number: 33207580945
$946.82 MSRP: $1238.83
You Save: $292.01 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Exchange. Output Shaft, Left; Axle Assembly
- Position: Rear Driver Side
- Replaced by: 33207580325
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2006 BMW 330i | Sedan(E90)
View related parts
BMW 330i Cv Axle Assembly Left
Part Number: 33217553563
$533.81 MSRP: $693.91
You Save: $160.10 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Exchange. Output Shaft, Left; Axle Assembly
- Position: Driver Side
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2006 BMW 330i | Sedan(E90)
View related parts
BMW 330i Cv Axle Assembly Rear Right
Part Number: 33217553564
$533.81 MSRP: $693.91
You Save: $160.10 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Exchange Output Shaft, Right; Axle Assembly
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2006 BMW 330i | Sedan(E90)
View related parts
BMW 330i Shafts Rear Right Cv Axle Shaft
Part Number: 33217504523
$753.74 MSRP: $792.67
You Save: $38.93 (5%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Exchange Output Shaft, Right; Axle Assembly
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2001-2005 BMW 330i | Sedan(E46)
View related parts
BMW 330i Rear Right Cv Axle Assembly
Part Number: 33207637444
$1052.01 MSRP: $1376.47
You Save: $324.46 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Output Shaft, Right; Axle Assembly
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2017-2018 BMW 330i | Sedan(F30)
View related parts
BMW 330i OUTPUT SHAFT, REAR LEFT
Part Number: 33208666073
$1028.37 MSRP: $1345.55
You Save: $317.18 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Axle Assembly, Axle Shaft
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2019-2023 BMW 330i | 4 Cyl 2.0 L GAS, Sedan(G20)
View related parts
BMW 330i OUTPUT SHAFT, REAR LEFT
Part Number: 33208487123
$1073.05 MSRP: $1404.00
You Save: $330.95 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2023-2024 BMW 330i | 4 Cyl 2.0 L GAS
- 2019-2020 BMW 330i | Sedan(G20)
View related parts
BMW 330i OUTPUT SHAFT, REAR RIGHT
Part Number: 33209452904
$1073.05 MSRP: $1404.00
You Save: $330.95 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Axle Assembly, Axle Shaft
- Position: Rear Passenger Side
- Replaced by: 33205A733B6
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2019-2020 BMW 330i | Sedan(G20)
View related parts
BMW 330i Output Shaft, Rear Left
Part Number: 33209896323
$1073.05 MSRP: $1404.00
You Save: $330.95 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Rear Driver Side
- Replaced by: 33205A74AC7
- Replaces: 33-20-8-689-571
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2019-2024 BMW 330i | 4 Cyl 2.0 L GAS, Sedan(G20)
View related parts
BMW 330i OUTPUT SHAFT, REAR RIGHT
Part Number: 33209896324
$1073.05 MSRP: $1404.00
You Save: $330.95 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Rear Passenger Side
- Replaced by: 33205A74AC8
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2019-2024 BMW 330i | 4 Cyl 2.0 L GAS, Sedan(G20)
View related parts
BMW 330i Cv Axle Assembly Rear Left
Part Number: 33217510623
$445.33 MSRP: $576.33
You Save: $131.00 (23%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Exchange. Output Shaft, Left; Axle Assembly
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2001-2005 BMW 330i | Sedan(E46)

| Page 1 of 2 |Next >

1-20 of 23 Results

BMW 330i Axle Shaft

If you are looking for OEM BMW 330i Axle Shaft, we highly recommend to shop with us. Not only do we offer the most budget friendly prices, but we also provide fast delivery. In addition, we have a hassle-free return policy on all genuine BMW 330i Axle Shaft that come backed by the manufacturer's warranty.

BMW 330i Axle Shaft Parts Questions & Experts Answers

Cv Axle Assembly Left
33217553563
Q: How to remove the front and rear driveaxles on BMW 330i?
A: For AWD models, when removing the front, start by having the vehicle on its wheels, remove the wheel trim/hub cap, and loosen the Axle Shaft retaining nut or bolt and the wheel bolts. Before loosening the Axle Shaft nut, use a hammer and punch to push out the staked portion of the nut. On F-series chassis models, always replace the Axle Shaft bolt and small compression spring whenever they are removed. Block the rear wheels, raise the vehicle front, support on jackstands, and take off the front wheel. Detach the ABS wheel speed sensor, set the brake caliper aside without disconnecting the brake fluid hose. Disconnect the stabilizer bar link from the strut and separate the tension strut and control arm from the knuckle. Push the Axle Shaft stub through the hub while pulling the steering knuckle outwards. Pry the inboard CV joint away from the front Differential housing. For the right Axle Shaft, pry against the bearing bracket. For installation, remove the snap-ring from the Axle Shaft's inboard end and install a new one. Lubricate the nut-to-wheel bearing area, tighten the nut to the needed torque without oiling the threads, stake the nut post-tightening, and add new inner joint retaining bolts and plates, tightening them to the necessary torque.For the rear, with the vehicle on its wheels, remove the wheel trim/hub cap and loosen the Axle Shaft retaining nut and wheel bolts. Push out the staked portion of the Axle Shaft nut using a hammer and punch. Block the front wheels, raise the rear, and support on jackstands before removing the rear wheel. For E-series chassis, if removing the left Axle Shaft, remove the exhaust system tailpipe. Loosen and remove the stabilizer bar mounts, pivot the bar downwards. Mark alignment, then loosen and remove bolts securing the Axle Shaft CV joint to the rear differential. Withdraw the outer CV joint from the hub assembly. Tap or press it out if needed and then remove the driveshaft.For F-series chassis models, remove the Axle Shaft nut, push the axle slightly inwards, support the rear differential, then remove the mounting bolt/nuts and lower the differential. Pry the inboard CV joint away from the rear differential housing until the Axle Shaft is free, slide the Axle Shaft out of the differential, and have a pan ready for spilled lubricant. For installation, note the following: On E-series chassis models, install new inner joint retaining bolts and plates and tighten. On F-series chassis models, check the dust plate, replace the circlip on the Axle Shaft's end, and coat the seal contact with differential oil. Slide the Axle Shaft into the rear differential until an audible click is heard. Reinstall the rear differential assembly and refill it. Lubricate the nut-to-hub flange area, tighten the nut without oiling the threads, and then stake the nut once tightened.

Related BMW 330i Parts

Browse by Year

2024 Axle Shaft 2023 Axle Shaft 2022 Axle Shaft 2021 Axle Shaft 2020 Axle Shaft 2019 Axle Shaft 2018 Axle Shaft 2017 Axle Shaft 2006 Axle Shaft 2005 Axle Shaft 2004 Axle Shaft 2003 Axle Shaft 2002 Axle Shaft 2001 Axle Shaft